23 documents found, page 1 of 3
Quantification of Residual Stress Relief by Heat Treatments in Austenitic Cladd...
Rebelo Kornmeier, Joana; Marques, Maria José; Gan, Weimin; Batista, António Castanhola; Paddea, Sanjooram; Loureiro, AltinoThe effect of the heat treatment on the residual stresses of welded cladded steel samples is analyzed in this study. The residual stresses across the plate's square sections were determined using complementary methods; applying diffraction with neutron radiation and mechanically using the contour method. The analysis of the large coarse grain austenitic cladded layers, at the feasibility limits of diffraction m...
Effect of Friction Stir Welding Techniques and Parameters on Polymers Joint Eff...
Pereira, Miguel A. R.; Amaro, Ana M.; Reis, Paulo N. B.; Loureiro, AltinoThe objective of current work is to analyse the influence of different welding techniques and welding parameters on the morphology and mechanical strength of friction stir welds (FSW) in polymers, based on data collected in the literature. In the current work, only articles that provide data on the joint efficiency, or sufficient information to estimate it are considered. The process using conventional tool is ...
Influence of tool geometry and process parameters on torque, temperature, and q...
Manuel, Neves; Beltrão, Daniel; Galvão, Ivan; Leal, Rui; Costa, José D.; Loureiro, AltinoIn the current investigation, the influence of the tool geometry, the position of the materials in the joint, the welding speed on the temperature and torque developed, and on the quality of the welds in dissimilar and tri-dissimilar T joints were analysed. The aluminium alloys used were AA2017-T4, AA6082-T6, and AA5083-H111 and the friction stir welds were performed with identical shoulder tools, but with eith...
Comparison of mechanical performance between friction-stir spot welded and adhe...
Reis, Paulo N. B.; Amaro, Ana Paula; Loureiro, AltinoThe main goal of this study is to compare the morphology and mechanical strength of friction stir spot welded (FSSW) joints and adhesive bonded stepped joints. The welded joints were produced by friction stir spot welding, while the adhesive bonded ones used an Araldite 420 A/B adhesive. All joints were subjected to morphology and microstructure analyses, microhardness tests, tensile-shear tests and local strai...
Nugget Formation and Mechanical Behaviour of Friction Stir Welds of Three Dissi...
Manuel, Neves; Galvão, Ivan; Leal, Rui M.; Costa, José D.; Loureiro, AltinoThe aim of this research was to investigate the influence of the properties of the base materials and welding speed on the morphology and mechanical behavior of the friction stir welds of three dissimilar aluminum alloys in a T-joint configuration. The base materials were the AA2017-T4, AA5083-H111, and AA6082-T6 alloys in 3 mm-thick sheets. The AA6082-T6 alloy was the stringer, and the other alloys were locate...
Aluminum-to-Steel Cladding by Explosive Welding
Carvalho, Gustavo H. S. F. L.; Galvão, Ivan; Mendes, Ricardo; Leal, Rui M.; Loureiro, AltinoThe production of aluminum-carbon steel and aluminum-stainless steel clads is challenging, and explosive welding is one of the most suitable processes to achieve them. The present work aims to investigate the coupled e ect of two strategies for optimizing the production of these clads by explosive welding: the use of a low-density interlayer and the use of a low-density and low-detonation velocity explosive mix...
Impact Welding of Materials
Galvão, Ivan; Loureiro, Altino; Mendes, RicardoRecent industrial criteria, focused on obtaining increasingly e cient structures, require the production of multimaterial components. However, the manufacturing requirements of these components are not met by conventional welding techniques. Alternative solid-state technologies, such as friction or impact-based processes, must be considered. Impact welding processes have the advantage of presenting a very short...
Explosive welding of aluminium to stainless steel using carbon steel and niobiu...
Carvalho, Gustavo; Galvão, Ivan; Mendes, R.; Leal, R. M.; Loureiro, AltinoThis work aimed to study aluminium to stainless steel explosive welds produced using two different interlayers: carbon steel and niobium. The use of each interlayer was analysed and compared microstructurally and mechanically using many characterisation techniques. The final joints using both interlayers presented favourable interfacial microstructure: waves on both interfaces. However, the joint using the carb...
Nugget formation and mechanical behaviour of friction stir welds of three dissi...
Neves, Manuel; Galvão, Ivan; Leal, Rui; Costa, José D.; Loureiro, AltinoThe aim of this research was to investigate the influence of the properties of the base materials and welding speed on the morphology and mechanical behavior of the friction stir welds of three dissimilar aluminum alloys in a T-joint configuration. The base materials were the AA2017-T4, AA5083-H111, and AA6082-T6 alloys in 3 mm-thick sheets. The AA6082-T6 alloy was the stringer, and the other alloys were locate...
Impact welding of materials
Galvão, Ivan; Loureiro, Altino; Mendes, RicardoRecent industrial criteria, focused on obtaining increasingly efficient structures, require the production of multimaterial components. However, the manufacturing requirements of these components are not met by conventional welding techniques. Alternative solid-state technologies, such as friction or impact-based processes, must be considered. Impact welding processes have the advantage of presenting a very sho...