7 documents found, page 1 of 1
The effects of mechanical alloying on the physical and thermal properties of Cu...
Antão, F.; Dias, Marta; Correia, J. B.; Galatanu, Andrei; Galatanu, M.; Mardolcar, U. V.; Myakush, A.; Cruz, Maria Margarida; Casaca, AntónioThe present work reports the production and key properties of the CuCrFeTiV high entropy alloy synthetized mechanical alloying and spark plasma sintering. The milled powders and the as-sintered samples were analysed through scanning electron microscopy, coupled with energy dispersive X-ray spectroscopy and particle induced X-ray emission. Magnetic properties together with electrical resistivity, thermal conduct...
The effects of mechanical alloying on the physical and thermal properties of Cu...
Antão, Francisco; Dias, Marta; Correia, J.B.; Galatanu, Andrei; Galatanu, M.; Mardolcar, U. V.; Myakush, A.; Cruz, M. M.; Casaca, AntónioABSTRACT: The present work reports the production and key properties of the CuCrFeTiV high entropy alloy synthetized mechanical alloying and spark plasma sintering. The milled powders and the as-sintered samples were analysed through scanning electron microscopy, coupled with energy dispersive X-ray spectroscopy and particle induced X-ray emission. Magnetic properties together with electrical resistivity, therm...
New WC-Cu composites for the divertor in fusion reactors
Dias, Marta; Pinhão, N.; Faustino, R.; Martins, Ricardo; Ramos, A. S.; Vieira, M. T.; Correia, J.B.; Camacho, E.; Fernandes, F. M. Braz; Nunes, B.ABSTRACT: The requirements for the divertor components of future fusion reactors are challenging and therefore a stimulus for the development of new materials. In this paper, WC-Cu composites are studied for use as thermal barrier between the plasma facing tungsten tiles and the copper-based heat sink of the divertor. Composite materials with 50% vol. WC were prepared by hot pressing and characterized in terms ...
WC-Cu thermal barriers for fusion applications
Dias, Marta; Guerreiro, F.; Tejado, Elena; Correia, J.B.; Mardolcar, U. V.; Coelho, M.; Palacios, T.; Pastor, Jose Ygnacio; Carvalho, Patricia AlmeidaABSTRACT: WC-Cu cermets have been devised for thermal barriers between the plasma facing tungsten tiles and the copperbased heat sink in the first wall of nuclear fusion reactors. Composite materials with 50 and 75 v/v% WC have been prepared by hot pressing at 1333 and 1423 K with pressures of 37 and 47 MPa, respectively. Microstructural changes have been investigated by scanning electron microscopy coupled wit...
The effects of tantalum addition on the microtexture and mechanical behaviour o...
Tejado, Elena; Carvalho, Patricia Almeida; Munoz, A.; Dias, Marta; Correia, J.B.; Mardolcar, U. V.; Pastor, Jose YgnacioTungsten (W) and its alloys are very promising materials for producing plasma-facing components (PFCs) in the fusion power reactors of the near future, even as a structural part in them. However, whereas the properties of pure tungsten are suitable for a PFC, its structural applications are still limited due to its low toughness, ductile to brittle transition temperature and recrystallization behaviour. Therefo...
The effects of tantalum addition on the microtexture and mechanical behaviour o...
Tejado, Elena; Carvalho, Patricia Almeida; Munoz, A.; Dias, Marta; Correia, J.B.; Mardolcar, U. V.; Pastor, Jose YgnacioTungsten (W) and its alloys are very promising materials for producing plasma-facing components (PFCs) in the fusion power reactors of the near future, even as a structural part in them. However, whereas the properties of pure tungsten are suitable for a PFC, its structural applications are still limited due to its low toughness, ductile to brittle transition temperature and recrystallization behaviour. Therefo...
Tungsten–nanodiamond composite powders produced by ball milling
Nunes, D.; Livramento, Vanessa; Mardolcar, U. V.; Correia, J.B.; Carvalho, Patricia AlmeidaThe major challenge in producing tungsten–nanodiamond composites by ball milling lies in successfully dispersing carbon nanoparticles in the metallic matrix while keeping carbide formation at a minimum. Processing windows for carbide minimization have been established through systematic variation of the nanodiamond fraction, milling energy and milling time. Materials characterization has been carried out by X-r...